Dan,
I forgot to mention… I would like to order 4 addition sets of those gloves, so 5 total please.
Jenn
From: Dan Enck [mailto:Dan@publicworkssupply.com]
Sent: Monday, October 06, 2014 11:30 AM
To: Jennifer Cline
Subject: RE: Estimate 6022 from Public Works Supply
I should have been more specific…I meant your Roll-up signs. On this quote you are getting 16 roll-up signs but only 8 of the aluminum stands. So you must have current inventory of some kind of roll-up sign stand on hand? I just want to make sure we have the correct setup.
Thanks,
Dan
From: Jennifer Cline [mailto:jcline@cityofmolalla.com]
Sent: Monday, October 06, 2014 11:26 AM
To: Dan Enck
Subject: RE: Estimate 6022 from Public Works Supply
I’m sure they do not. I was assuming the 2 slow/stop paddles were quoted with new stands/poles. If not, please include.
Thanks,
Jenn
From: Dan Enck [mailto:Dan@publicworkssupply.com]
Sent: Monday, October 06, 2014 8:29 AM
To: Jennifer Cline
Subject: RE: Estimate 6022 from Public Works Supply
One last thing before I get everything moving and sorry if I already asked this:
The signs quoted have a 1” (Outside diameter) square tube that fits into a 1.25” (Outside diameter) opening on the stands, and they “snap” together with a detent button. Do your current signs resemble this setup? I want to avoid sending you signs that don’t fit into your stands!!
Dan
From: Jennifer Cline [mailto:jcline@cityofmolalla.com]
Sent: Friday, October 03, 2014 4:40 PM
To: Dan Enck
Subject: RE: Estimate 6022 from Public Works Supply
Hi Dan,
I’m going to change my mind on the anchors. After thinking about it, it’s very possible we may replace those ramps in the next 5 years.
Thank you for taking the time to find them however.
Jenn
From: Dan Enck [mailto:Dan@publicworkssupply.com]
Sent: Friday, October 03, 2014 4:38 PM
To: Jennifer Cline
Subject: RE: Estimate 6022 from Public Works Supply
How many of the mechanical anchors would you like per mat? It didn’t specify how many per mat to use…thoughts?
Dan
From: Jennifer Cline [mailto:jcline@cityofmolalla.com]
Sent: Friday, October 03, 2014 4:30 PM
To: Dan Enck
Cc: Garrett Edmunds; Darren Penni
Subject: RE: Estimate 6022 from Public Works Supply
Hi Dan,
Please process the attached order with the $81.75 Stand, Dynalite, Aluminum selection.
I also would like to order 1 XL large pair of the Alycore gloves.
Please feel free to give me a call if you have any questions.
Jennifer Cline, P.E.
City of Molalla
Public Works Director
O: 503.829.6855 Ext. #218
F: 503.829.3676
"
From: Dan Enck [mailto:Dan@publicworkssupply.com]
Sent: Tuesday, September 30, 2014 9:44 AM
To: Jennifer Cline (jcline@cityofmolalla.com)
Subject: Estimate 6022 from Public Works Supply
Hi Jennifer!
Ok, so I found that there are some mechanical fasteners for these ADA mats. I included the price for each fastener on the quote. Here is their statement from their installation instructions:
Also, I called Majestic Glove (our primary source for gloves) to discuss your needle situation. While Kevlar sewn gloves will help protect against cuts, they won’t necessarily help with possible punctures. We can most definitely get you Kevlar gloves but they recommend gloves that have puncture testing that meets certified puncture tests.
So the ways the puncture gloves are rated are by the “layers”. For example this glove:
It has 2 layers of protection in the palm, one layer on back of hand, one layer in fingers. The 2 layers withstood 6.61 pounds of pressure directly with a needle before puncture, 1 layer withstood 3.56 pounds.
These gloves are $15.75 per pair. They can be ordered by the each instead of dozens. Kevlar lined leather gloves run $13.67 and must be ordered in full dozens. I hope this helps!
Regards,
Dan Enck
Public Works Supply, Inc
503-678-2981 office | 503-678-2983 fax
10751 Oak Street #2, PO Box 702
Donald, OR 97020